BUILDING WAREHOUSE Reflective Insulation Roll Foam Core Radiant Barrier R8 4X100
US ENERGY PRODUCTS 5mm (1/4INCH THICK) Reflective Insulation Roll, Foam Core Radiant Barrier – Engineered Foil. ALL IN ONE PRODUCT: INSULATION + RADIANT BARRIER + VAPOR BARRIER + SOUND BARRIER. THIS IS NOT A CHEAP DOUBLE BUBBLE REFLECTIVE INSULATION, WE HAVE A SUPERIOR QUALITY REFLECTIVE FOAM CORE INSULATION, COMMERCIAL GRADE!!! WHERE TO INSULATE? Attics, Ceilings, Walls, Steel Buildings, POLE BARNS, Roofing, Concrete Floor, Radiant Heat in a Concrete Floor, Radiant Heating Under a Wood Floor, Cathedral Ceiling, Water Heater Tank, Radon Barrier, Water Pipe and Air Duct, Reflective Ceiling System, Behind a Hot Water Radiator, Crawl Space, In Ground Swimming Pools, Shed, Fish & Hunting Shelter, Cooling Room, Cold Chamber or Wine Cellar, Concrete Block Wall, Cavity Wall for Metallic Studs in Commercial Buildings, Foundation Wall, Above Ground Swimming Pools, Quanset Hut, House Wrap. EXTREMELY EFFECTIVE – Reflects 95% of radiant energy, perfect RADIANT BARRIER. R-value up to 15.67 ( with one layer), up to 21.10 ( with two layers).VAPOR BARRIER – prevents condensation, unaffected by humidity and moisture, mold resistant!MEETS OR EXCEEDS ALL ASTM C1313 STANDARDS – Class A Fire Rating (E84 with E2599 mounting). Corrosion resistance according to D3310 is achieved by a proprietary clear coating applied to the Engineered Foil surface.INDUSTRIAL / COMMERCIAL GRADE – US ENERGY PRODUCTS -5mm Foam Core Reflective Insulation is TEAR & PUNCTURE PROOF, but you can easily cut it with utility scissors. Both sides reflects 95% of the radiant heat.PAYS FOR ITSELF – by reducing heating cost in winter and cooling cost in summer. NON TOXIC – will not irritate skin, eye or throat. Non allergic.SIZE: 4FT X 100FT
Read More200sqft Reflective Foam Core WAREHOUSE BUILDING Insulation 24″ X 100ft 5MM R8-24
US ENERGY PRODUCTS 5mm (1/4INCH THICK) Reflective Insulation Roll, Foam Core Radiant Barrier – Engineered Foil. ALL IN ONE PRODUCT: INSULATION + RADIANT BARRIER + VAPOR BARRIER + SOUND BARRIER. THIS IS NOT A CHEAP DOUBLE BUBBLE REFLECTIVE INSULATION, WE HAVE A SUPERIOR QUALITY REFLECTIVE FOAM CORE INSULATION, COMMERCIAL GRADE!!! WHERE TO INSULATE? Attics, Ceilings, Walls, Steel Buildings, POLE BARNS, Roofing, Concrete Floor, Radiant Heat in a Concrete Floor, Radiant Heating Under a Wood Floor, Cathedral Ceiling, Water Heater Tank, Radon Barrier, Water Pipe and Air Duct, Reflective Ceiling System, Behind a Hot Water Radiator, Crawl Space, In Ground Swimming Pools, Shed, Fish & Hunting Shelter, Cooling Room, Cold Chamber or Wine Cellar, Concrete Block Wall, Cavity Wall for Metallic Studs in Commercial Buildings, Foundation Wall, Above Ground Swimming Pools, Quanset Hut, House Wrap. EXTREMELY EFFECTIVE – Reflects 95% of radiant energy, perfect RADIANT BARRIER. R-value up to 15.67 ( with one layer), up to 21.10 ( with two layers).VAPOR BARRIER – prevents condensation, unaffected by humidity and moisture, mold resistant!MEETS OR EXCEEDS ALL ASTM C1313 STANDARDS – Class A Fire Rating (E84 with E2599 mounting). Corrosion resistance according to D3310 is achieved by a proprietary clear coating applied to the Engineered Foil surface.INDUSTRIAL / COMMERCIAL GRADE – US ENERGY PRODUCTS -5mm Foam Core Reflective Insulation is TEAR & PUNCTURE PROOF, but you can easily cut it with utility scissors. Both sides reflects 95% of the radiant heat.PAYS FOR ITSELF – by reducing heating cost in winter and cooling cost in summer. NON TOXIC – will not irritate skin, eye or throat. Non allergic.SIZE: 4FT X 50FT
Read MoreBUILDING WAREHOUSE Reflective Insulation Roll Foam Core Radiant Barrier R8 4X250
US ENERGY PRODUCTS 5mm (1/4INCH THICK) Reflective Insulation Roll, Foam Core Radiant Barrier – Engineered Foil. ALL IN ONE PRODUCT: INSULATION + RADIANT BARRIER + VAPOR BARRIER + SOUND BARRIER. THIS IS NOT A CHEAP DOUBLE BUBBLE REFLECTIVE INSULATION, WE HAVE A SUPERIOR QUALITY REFLECTIVE FOAM CORE INSULATION, COMMERCIAL GRADE!!! WHERE TO INSULATE? Attics, Ceilings, Walls, Steel Buildings, POLE BARNS, Roofing, Concrete Floor, Radiant Heat in a Concrete Floor, Radiant Heating Under a Wood Floor, Cathedral Ceiling, Water Heater Tank, Radon Barrier, Water Pipe and Air Duct, Reflective Ceiling System, Behind a Hot Water Radiator, Crawl Space, In Ground Swimming Pools, Shed, Fish & Hunting Shelter, Cooling Room, Cold Chamber or Wine Cellar, Concrete Block Wall, Cavity Wall for Metallic Studs in Commercial Buildings, Foundation Wall, Above Ground Swimming Pools, Quanset Hut, House Wrap. EXTREMELY EFFECTIVE – Reflects 95% of radiant energy, perfect RADIANT BARRIER. R-value up to 15.67 ( with one layer), up to 21.10 ( with two layers).VAPOR BARRIER – prevents condensation, unaffected by humidity and moisture, mold resistant!MEETS OR EXCEEDS ALL ASTM C1313 STANDARDS – Class A Fire Rating (E84 with E2599 mounting). Corrosion resistance according to D3310 is achieved by a proprietary clear coating applied to the Engineered Foil surface.INDUSTRIAL / COMMERCIAL GRADE – US ENERGY PRODUCTS -5mm Foam Core Reflective Insulation is TEAR & PUNCTURE PROOF, but you can easily cut it with utility scissors. Both sides reflects 95% of the radiant heat.PAYS FOR ITSELF – by reducing heating cost in winter and cooling cost in summer. NON TOXIC – will not irritate skin, eye or throat. Non allergic.SIZE: 4FT X 250FT (2 ROLLS OF 4X100 AND 1 ROLL OF 4X50)
Read MoreAutomotive Sound Deadening Reflective Insulation Heat Barrier Noise Proof 2×5
US ENERGY PRODUCTS 5mm (1/4INCH THICK) Reflective Insulation Roll, Foam Core Radiant Barrier – Engineered Foil. SIZE: 2FT WIDE X 5FT LONG ALL IN ONE PRODUCT: INSULATION + RADIANT BARRIER + VAPOR BARRIER + SOUND BARRIER. THIS IS NOT A CHEAP DOUBLE BUBBLE REFLECTIVE INSULATION, WE HAVE A SUPERIOR QUALITY REFLECTIVE FOAM CORE INSULATION, COMMERCIAL GRADE!!! WHERE TO INSULATE? Attics, Ceilings, Walls, Steel Buildings, POLE BARNS, Roofing, Concrete Floor, Radiant Heat in a Concrete Floor, Radiant Heating Under a Wood Floor, Cathedral Ceiling, Water Heater Tank, Radon Barrier, Water Pipe and Air Duct, Reflective Ceiling System, Behind a Hot Water Radiator, Crawl Space, In Ground Swimming Pools, Shed, Fish & Hunting Shelter, Cooling Room, Cold Chamber or Wine Cellar, Concrete Block Wall, Cavity Wall for Metallic Studs in Commercial Buildings, Foundation Wall, Above Ground Swimming Pools, Quanset Hut, House Wrap. EXTREMELY EFFECTIVE – Reflects 95% of radiant energy, perfect RADIANT BARRIER. R-value up to 15.67 ( with one layer), up to 21.10 ( with two layers).VAPOR BARRIER – prevents condensation, unaffected by humidity and moisture, mold resistant!MEETS OR EXCEEDS ALL ASTM C1313 STANDARDS – Class A Fire Rating (E84 with E2599 mounting). Corrosion resistance according to D3310 is achieved by a proprietary clear coating applied to the Engineered Foil surface.INDUSTRIAL / COMMERCIAL GRADE – US ENERGY PRODUCTS -5mm Foam Core Reflective Insulation is TEAR & PUNCTURE PROOF, but you can easily cut it with utility scissors. Both sides reflects 95% of the radiant heat.PAYS FOR ITSELF – by reducing heating cost in winter and cooling cost in summer. NON TOXIC – will not irritate skin, eye or throat. Non allergic.SIZE: 36INCH X 10FT
Read MoreTouch N Seal 600 BF Spray Foam Insulation Kit 1.75 FR Closed Cell, Free Shipping
Spray Foam Kit 600 – Closed Cell, Quick Cure Foam Kit 600 is a completely self-contained, 2-component foam system that is portable and disposable. These Quick Cure, Closed Cell polyurethane foam insulation kits are perfect for insulating and air sealing. Foam Kit 600 provides up to six hundred board feet of polyurethane spray foam. Designed for larger insulating, sealing, patching, and filling applications. Complete with color-coded hoses, ergonomic foam applicator — everything you need to get started foaming. Each Kit 600 includes: Two Cylinders (Components A & B)Anti-Crossover Foam Applicator with 15’ HoseExtra Nozzles (5 Cone; 5 Fan)Chemical Resistant GlovesAssembly WrenchPetroleum Jelly *DUE TO EPA REGULATIONS, THIS PRODUCT CANNOT BE SHIPPED TO THE FOLLOWING STATES: CALIFORNIA, COLORADO, DELAWARE, MAINE MARYLAND, MASSACHUSETTS, NEW JERSEY, NEW YORK, RHODE ISLAND, VERMONT, VIRGINIA, WASHINGTON *NOTICE: You can find our LOW GWP HFO foam kit available to ship to all states here. What You are Buying: You are purchasing a brand new, 600 board foot kit of Quick Cure, Polyurethane, High Density, Closed-Cell spray foam. Other size and types are available in our Ebay Store. Stored in Temperature Controlled Warehouse. Chemicals guaranteed to be properly in solution when it ships from our facility due to proper storage temperatures (typically kept at 75 – 85 degrees) We only ship fresh foam (typically less than 1 month old)The spray foam applicator controls the flow of the chemical componentsFan and Conical nozzle typesTechnical support is our strength, and we are proud of our world class customer support ENERGY EFFICIENT SOLUTIONS IS AN INDEPENDENTLY OWNED AND OPERATED DISTRIBUTOR OF TOUCH-N-SEAL AND ITS RELATED PRODUCTS. THESE PRODUCTS ARE INTENDED FOR PROFESSIONAL USE ONLY. Key Features Key Features: Coverage area: 600 sq. ft. at 1″ thick Expanded Volume: 50 ft³ Tack Free: 30-60 sec. Cutable in 2 – 5 min. Full Cure Time: Approx. 1 hour Type: Polyurethane Closed Cell: Yes (The only foam that truly stops water and air infiltration) Density: 1.75 lbs/ft³Aged R-Value: 6.2 @ 1” (25mm) Shipping Weight: 115 lbs. (2 Packages) Required Safety Equipment: More Details Other Online Docs: Operating Instructions Data Sheet MSDS-A MSDS-B Kit includes: Component A Component B 15 ft Hose Set Dispensing Gun 10 spray nozzlesOperating Instructions Recommended Accessories: Safety Kit (Respirator, Goggles, Coveralls, Gloves) Ebay Store Please Read the Following:Keys to Using Disposable Spray Foam Insulation KitsNote: The following instructions are not unique to Touch ‘n Seal Spray Foam Kits. All brands of SPF Kits have similar requirements to those listed below, and special precautions must be taken when spraying spray foam insulation.· Operating Instructions· Please read through the manufacturer’s operating instructions prior to using any SPF kit.· Temperature, Temperature, Temperature!· Temperature – All SPF kits need to be conditioned to the proper temperature prior to use. In general, optimal core temperature is 75-85 F.The single most important factor is maintaining proper core temperature. Temperatures affect both the viscosity of the liquids and pressures in the tanks. Failure to maintain temperature within the acceptable ranges will result in inconsistent foam and lower yields. If your tanks have arrived off the truck cold it can take several days for the chemical to reach room temperature.· Shake Well· Remove each tank from its box and rock back and forth on one bottom edge for at least 2 minutes.· “30 second rule”· Whenever you stop spraying for 30 seconds or more, you will need to replace the nozzle. Failure to do so may result in damage tothe gun.· Test Shot-· A small test sample should be sprayed into a trash can without a nozzle prior to using the kit in the final application. Look for 2 steady streams from both sides. Then, during product application, look for firm, pale-yellow colored foam. Anything brittle or runny is off-ratio foam. STOP AND CALL if you encounter anything other than very hard foam.· Upright Position· The tanks must remain in the upright position (valve at the top) while spraying foam or yield issues can occur due to off-ratio spraying. Placing each tank in its box will help to keep it upright.· Unspent Tank Storage· Leave a cured nozzle on the gun after use for storage. This provides a seal for the hoses and gun so that air does not seep into thehoses (which could potentially cause a slight hardening of one component or the other inside the hoses). If this is not done, it is possibleto experience some yield issues with the foam or potentially even cause a complete blockage in one hose. Purge hose/gun for 15 secondsevery 7-10 days of storage between uses to keep the foam in the hoses fresh, leaving the spent nozzle tip on the end of the gun after eachpurging.· Apply foam in 1-2 lifts· Apply foam in 1-2 layers per pass. If more than 1-2 is applied at one time, the foam is compacted during spraying which cancause yield issues. Foam sprayed thicker than 2 per pass will have a higher density and therefore will cover less square footage.· Open Valves 100%, Close when not in Use · Both A & B side tanks must be opened 100% (both open counter-clockwise). When not in use, close the valves 100%. Contact and Shipping * THIS PRODUCT CANNOT BE SHIPPED TO THE FOLLOWING STATES:COLORADO, CALIFORNIA, MARYLAND, MASSACHUSETTS, NEW JERSEY, NEW YORK, VERMONT, VIRGINIA, WASHINGTON Feel free to message us through the Ebay messaging system with any questions or concerns. This listing has free shipping. One kit ships via UPS Ground, so please choose the UPS Ground option for your shipping method. Since these kits contain hazardous materials, UPS ground also requires a signature in order for these kits to be delivered to your location. If you need two or more kits, please choose flat rate freight as your shipping method as this is most likely how it will ship. Orders processed by 3:00pm CT, usually ship same day. If you live in the Dallas / Fort Worth area, pickup is available at our warehouse upon request. A phone number is required for International shipments and helps to ensure a timely delivery for domestic shipments. Sales tax of 8.25% applies to sales within the state of Texas. Terms of Sale By purchasing this product, you agree to the following terms of use. I understand that all Touch-N-Seal and related products are intended for PROFESSIONAL USE ONLY. When applying foam always consult the product MSDS, wear proper personal protective equipment as recommended by the manufacturer, ensure good ventilation during application, and make sure the building being sprayed is vacated during application and for a period of time following installation. For additional information on health and safety issues related to spray foam, visit www.spraypolyurethane.org. Touch-N-Seal products contain diisocyanate. This chemical may cause sensitization by inhalation and/or direct skin contact and can be an irritant to the eyes, nose and throat. Sensitization may become apparent through coughing, pulmonary secretions, chest pain, breathing difficulty and/or asthma. For these reasons, when using two component polyurethane spray foams we recommend following or participating in a respiratory program. All Touch-N-Seal® two-component polyurethane spray foams should always be used in conjunction with a certified respirator program in addition to safety glasses or goggles, nitrile gloves, and clothing that protects from skin exposure. Required respirators must be NIOSH approved and medical evaluation and training must be attained before use. I have read the DAP Safe Use, Storage, and Handling guidelines and understand the hazards and proper safety, handling, and personal protective equipment requirements associated with the use of the product. Return Policy Returns of unused and unopened items are only accepted with prior authorization. All returned items are subject to a 25% restocking and repackaging fee. Return shipping and shipping cost is the sole responsibility of the customer. No refunds of shipping and handling expenses are given. Refunds will be issued in the form of credit card adjustment, by Paypal, or by check at our discretion. WARNING – UPS will not accept this package from you unless you as the shipper have proper HAZMAT certification and are a registered HAZMAT shipper. About Energy Efficient Solutions Saving money through energy efficiency. Energy Efficient Solutions has been a market leader in energy efficiency for both residential and commercial applications since 2002. We strive to provide superior customer support and excellent product quality for all of our customers. For any questions regarding our products, message us through the Ebay messaging system. Touch-N-Seal® is backed by DAP Products Inc., a leading manufacturer and supplier of caulks, sealants, foam, adhesives, and repair products with a history of first-to-market innovations with trusted, quality, reliable and long-lasting products for professional contractors, remodelers and do-it-yourselfers. We at Energy Efficient Solutions LLC have been selling spray foam since 2008, and we pride ourselves on our reputation and top notch technical expertise and customer service. What’s Included Touch ‘n Seal Quick Cure Foam Kit, 600 square feet at 1 inch thick. (Component A, Component B, Hoses, Gun, and Tips) Payment Terms We accept PayPal, Visa, MasterCard, Discover, AMEX Shipping Terms (1) kit ships via UPS Ground in 2 boxes. (2 or more) kits will ship on a pallet via LTL freight service. Residential – Please provide a phone number as the freight company will need to call you to arrange the delivery. Someone must be present to help unload and to receive the shipment. Excellent to do business with! Great seller Received product quicky and in good condtion, good experience. Fast shipping. Great communication. Thank you!! Item arrived just as described, a pleasure to do business with. Excellent seller….highly recommended. Thanks! — arnurius great to deal with, second order fast shipping A+ — hillmank Lightning fast shipping… Smooth transaction… Thank you!!! — crazycat4398 Fast delivery and exactly as described Fast.Honest. Great communication, Item as described. A+++++ — mikekrebis Very fast and item as promised. Good ebaying — judyk4749
Read MoreINTERTOOL STORM Pro Expanding Spray Foam Gun Applicator Teflon Coated PT08-0606
[Reusable Foam Dispenser]: Easy to use insulating foam gun for applying polyurethane insulation and sealant foam. Foam remains pressurized and uncured in gun for up to 30 days when stored with foam canister attached and flow control knob closed. Requires thorough cleaning when canister is removed[Fully Coated in Easy Clean Material]: Covered with protective PTFE non-stick material to easily wipe away external foam and flush out remaining internal foam build-up[Less Mess and Wasted Foam]: Dispenses only the amount you need and reduces foam waste. Includes patented easy-turn flow control knob for adjustable bead size. Plus 4 tip attachments and a grout scraper for a clean finish[Use With Twist-on Can]: Intended for use with twist-on foam sealant and cleaner cans, such as Great Stuff Pro 24 oz screw-on canisters. Simply align the canister thread with the gun basket thread and screw on until secured. NOT compatible with straw or tube tipped canisters[INTERTOOL has YOU Covered]: 3 year warranty against manufacturer’s defects. We are always available to resolve any issue and answer to your needs. Our community is our #1 priority The INTERTOOL Professional Foam Gun Applicator PT-0606 effectively applies sealant with full and precise user control at a greater yield. Designed to be easily managed with a smooth trigger and flow control knob that promotes unrestricted flow while saving you money on wasted straw foam cans. ABS Plastic handle ensures a steady grip, and is suitable for time enduring, stress free application. Built to last with wear-resistant and durable component materials that are easy to clean. Easily take care of unwanted voids, cracks, and breaches. The INTERTOOL Professional Expanding Foam Gun PT-0606 is ideal for professional contractors and DIY enthusiasts.Compatibility:Supports most foam sealant and cleaner twist canisters such as AdvanTech and Great Stuff Pro Gaps & Cracks, Window & Door, Wall & Floor Construction Adhesive, and CleanerMaterial:Body & Connector / Holder: AluminumBarrel & Needle: Stainless SteelTip: CopperHandle: ABS PlasticHow to use the INTERTOOL Professional Foam Sealant Gun PT-0606:1) Retrieve a compatible sealant twist/screw canister. Do NOT use with straw or tube tipped canisters. Ensure to wear the proper safety equipment according to the foam canister’s instructions2) Shake the canister as instructed on the foam canister for a thorough mixture and remove the canister cover3) Ensure that the gun’s flow control knob is in the closed position by turning the knob all the way in a clockwise direction4) Place the canister in an upright position on a stable surface. Align the foam gun’s canister connection point with the thread on the top of the upright canister and tighten. Note: screw until finger-tight; do not over-tighten5) The foam gun is now ready for use. Grip the foam gun, point at a test surface, and gently squeeze the trigger while activating the flow control knob by twisting it counter-clockwise until the desired bead size / flow amount is reached6) Once the desired bead size / flow amount is reached, place the tip of the gun against the objective and slowly apply pressure to the trigger to begin the foam application7) When finished, twist the control knob clockwise until closed. The foam gun can be left attached to the canister with the canister stored right side up for up to 30 days, or as specified on the foam canister instructions. Ensure to close the flow control knob when stored. The canister can also be removed and compatible cleaning solution should be applied promptly to remove any residual foam left in or on the gun8) Ensure to run cleaning solution through the gun until no further foam residue remains. Remove cleaning solution can after cleaning. Foam gun can be re-used with the same canister or a new canisterUse Caution:Only point foam gun towards the project objectiveRecommended careful cleaning and maintenance for consistent product resultsStore safely out of reach of children
Read MoreDouble Bubble Reflective Foil Insulation (4 X 125 Ft Roll) Industrial Strength
Double Bubble Reflective Foil Insulation (4 X 125 Ft Roll) Industrial Strength. 7 rolls for sale. 500 sqft per roll
Read MoreOwens Corning 320 SQFT 10 bags of R49 Unfaced 16 x 48 Fiberglass Fits 2×12
It is available unfaced, or faced with either a kraft or foil vapor retarder. With less dust than other fiberglass products, EcoTouch PINK Fiberglass insulation has excellent stiffness and recovery characteristics.
Read MoreOwens Corning 320 SQFT 10 bags of R49 Kraft Faced 16 x 48 Fiberglass Fits 2×12
It is available unfaced, or faced with either a kraft or foil vapor retarder. Kraft and standard foil facings will burn and cannot be left exposed. With less dust than other fiberglass products, EcoTouch PINK Fiberglass insulation has excellent stiffness and recovery characteristics.
Read Moreinditherm hemp insulation battens
Ideal for eco-friendly construction, insulation, or sustainable building projects. ✔ Suitable for trade or DIY use.
Read More