Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 1 case – 2 rolls 6″ x 100′ of vulcanized butyl COVER tape used to seal flat roof top areas, perimeter edge termination detail and other FLAT EPDM roof joints. NOT TO BE USED FOR FLASHING DETAIL! THIS PRODUCT IS COMPRISED OF CURED EPDM RUBBER LAMINATED TO UNCURED BUTYL TAPE. Need to use primer activator to prime the flat area before applying the 6″ cover tape. This is 1 case, 2 – 6″ x 100′ rolls case, 2 rolls total and weighs 63 lbs per case FREE SHIPPING 48 STATES Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii

Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 1 roll 6″ x 50′ of vulcanized butyl flashing tape used to seal flash around roof top detail projections overlapping pieces of EPDM deck sheet roofing to form a watertight seal. Need to use primer activator to prime the seam area before applying the 6″ flashing tape. SELF VULCANIZING FLASHING JOINTS All FLASHING DETAIL: shall be sealed using 6″ OR 12″ SELF VULCANIZING FLASHING TAPE. All joints shall be shingled to shed water toward the drains, scuppers, etc. Contact surfaces for the FLASHING TAPE shall be cleaned to remove construction dirt using a light application of unleaded gas on a clean, lint-free rag. After cleaning apply primer to surfaces before applying seam tape. The FLASHING TAPE shall be securely bonded to the deck sheet along the previously marked bottom sheet. The flashing shall be formed from side to side to insure a minimum of 2″ overlap of the flashing beyond any edge piece. The release paper shall be carefully removed without disturbing the placement of the flashing or deck sheet. The lap joint shall be “walked in” to fix placement and thoroughly rolled with a 2″ metal roller in the direction perpendicular to the length of the joint. This is 1 roll – 6″ x 50′ and weighs 17 lbs Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii

Lottes Roofing 126 Point West BlvdSt. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” This is 1 – 4 gal pail of Latex bonding adhesive 40 lbs and is Class C-60 The actual can may be white or a different color in lieu of black, but the application instructions are the same as the product is exactly the same regardless of the exterior can color. Summary of My Selling PoliciesPaymentAll Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPalFeesNo sales taxes UNLESS in specific states localsShippingUS and InternationalDelivery24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidaysRefunds & ReturnsReturns accepted on qualified items with RGA return number BID WITH CONFIDENCE Not recommended to be used in temperatures lower than 50*. Temperature needs to be above 50* for 24 hours for full cure.FREE DELIVERY IN 48 states! Please provide your shipping address, city, state and zip code Check out my other items This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a latex based single surface bonding adhesive with coverage of about 400 sq. ft. per pail. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application. This adhesive is a SINGLE surface laminate adhesive that is to be used in a WET condition. Please allow time for the adhesive to become “tacky” which usually occurs in about 5 minutes or so.DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing membrane while the adhesive is Tacky NOT WET. So 1- 4 gal pail will cover about 300 – 400 square feet of finished roof area. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required. · 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards.· 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8″ without risk of possible adhesion issues.· 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive time to become “tacky”. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.· 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pieces of EPDM deck sheet together.· 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.Seam tape application if required to join 2 sheets together•Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. •Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area•Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2″ out from the edges of the bottom sheet. •Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. •With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. •Remove the paper backing by pulling out from under the top sheet at a 45ºangle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii

Lottes Roofing 126 Point West BlvdSt. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” This is 2 – 1 gal pail of Latex bonding adhesive 24 lbs and is Class C-60 The actual can may be white or a different color in lieu of black, but the application instructions are the same as the product is exactly the same regardless of the exterior can color.Summary of My Selling PoliciesPaymentAll Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPalFeesNo sales taxes UNLESS in specific states localsShippingUS and InternationalDelivery24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidaysRefunds & ReturnsReturns accepted on qualified items with RGA return numberContact Me BID WITH CONFIDENCE Not recommended to be used in temperatures lower than 50*. Temperature needs to be above 50* for 24 hours for full cure. Please provide your shipping address, city, state and zip code Check out my other items This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a latex based single surface bonding adhesive. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application. Coverage is about 110 sq. ft. per pail. This adhesive is a SINGLE surface laminate adhesive that is NOT to be used in a WET condition. Please allow time for the adhesive to become “tacky” which usually occurs in about 5 minutes or so. DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing membrane while the adhesive is Tacky NOT WET. So 3- 1 gal pail will cover about 330 square feet of finished roof area. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required. · 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards.· 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8″ without risk of possible adhesion issues.· 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive time to become “tacky”. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.· 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pieces of EPDM deck sheet together.· 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.Seam tape application if required to join 2 sheets together•Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. •Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area•Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2″ out from the edges of the bottom sheet. •Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. •With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. •Remove the paper backing by pulling out from under the top sheet at a 45ºangle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii